28 04 2014

QUESTION 101
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)

A.    Router(config)# router ospf 0
B.    Router(config)# router ospf 1
C.    Router(config)# router ospf area 0
D.    Router(config-router)# network 192.168.16.0 0.0.0.255 0
E.    Router(config-router)# network 192.168.16.0 0.0.0.255 area 0
F.    Router(config-router)# network 192.168.16.0 255.255.255.0 area 0

Answer: BE
Explanation:
In the router ospf
command, the ranges from 1 to 65535 so o is an invalid number -> but To configure OSPF, we need a wildcard in the “network” statement, not a subnet mask. We also need to assgin an area to this process -> .

QUESTION 102
What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?

A.    2
B.    8
C.    16
D.    unlimited

Answer: B
Explanation:
maximum-paths (OSPF)
To control the maximum number of parallel routes that Open Shortest Path First (OSPF) can support, use the maximum-paths command.
Syntax Description

Command Default
8 paths

QUESTION 103
OSPF routing uses the concept of areas. What are the characteristics of OSPF areas? (Choose Three.)

A.    Each OSPF area requires a loopback interface to be configured.
B.    Areas may be assigned any number from 0 to 65535.
C.    Area 0 is called the backbone area.
D.    Hierarchical OSPF networks do not require multiple areas.
E.    Multiple OSPF areas must connect to area 0.
F.    Single area OSPF networks must be configured in area 1.

Answer: BCE
Explanation:
Definition of OSPF areas: An OSPF network may be structured, or subdivided, into routing areas to simplify administration and optimize traffic and resource utilization. Areas are identified by 32-bit numbers, expressed either simply in decimal, or often in octet-based dot-decimal notation, familiar from IPv4 address notation.
See discussion following Cisco Learning discussion.
https://learningnetwork.cisco.com/message/90832

QUESTION 104
Which characteristics are representative of a link-state routing protocol? (Choose three.)

A.    provides common view of entire topology
B.    exchanges routing tables with neighbors
C.    calculates shortest path
D.    utilizes event-triggered updates
E.    utilizes frequent periodic updates

Answer: ACD
Explanation:
Each of routers running link-state routing protocol learns paths to all the destinations in its “area” so we can say although it is a bit unclear.
Link-state routing protocols generate routing updates only (not the whole routing table) when a change occurs in the network topology so
Link-state routing protocol like OSPF uses Dijkstra algorithm to calculate the shortest path -> . Unlike Distance vector routing protocol (which utilizes frequent periodic updates), link-state routing protocol utilizes event-triggered updates (only sends update when a change occurs) ->

QUESTION 105
What information can be used by a router running a link-state protocol to build and maintain its topological database? (Choose two.)

A.    hello packets
B.    SAP messages sent by other routers
C.    LSAs from other routers
D.    beacons received on point-to-point links
E.    routing tables received from other link-state routers
F.    TTL packets from designated routers

Answer: AC

If you want to pass the Cisco 100-101 Exam sucessfully, recommend to read latest Cisco 100-101 Dump full version.

100-101 Answers, 100-101 Questions, Cisco 100-101 Dumps, Cisco 100-101 Exam

2014 Cisco 100-101 Exam Dump(91-100) Official 2014 Latest Cisco 300-206 Dump Free Download(1-10)!