28 06 2017
[2017 News]Valid Braindump2go 352-001 Exam Dump PDF 499q Offer[1-10]
2017/June New Cisco 352-001 Exam Dumps with PDF and VCE Updated in www.Braindump2go.com Today for Free Download!
100% Real Exam Questions! 100% Exam Pass Guaranteed!
1.|2017 New 352-001 Exam Dumps (PDF & VCE) 499Q&As Download:
http://www.braindump2go.com/352-001.html
2.|2017 New 352-001 Exam Questions & Answers Download:
https://drive.google.com/drive/folders/0B75b5xYLjSSNSUNBNi1aYkpfOTQ?usp=sharing
QUESTION 1
A company plans to include Nonstop Forwarding and Bidirectional Forwarding Detection as a part of their network redundancy plan. In which two ways do NSF and BFD work together when different hardware platforms are compared? (Choose two.)
A. During supervisor engine or routing engine failover, the NSF feature will always ensure that the BFD
at the peer router will not trigger a link down independent of the used hardware platform.
B. At some hardware platforms, BFD and NSF are not supported together. During supervisor engine or
routing engine failover, the BFD at the peer router will trigger a link down.
C. To ensure that BFD at the peer router will not trigger a link down during NSF, the BFD packets must
be processed fast enough, and, during supervisor engine or routing engine failover, by processing the
BFD independent from the supervisor engine or routing engine.
D. Because BFD is always processed at the line cards (not at the supervisor engine or routing engine),
a supervisor engine or routing engine failover will not affect the BFD peer router.
E. Because BFD is always processed at the supervisor engine or routing engine, a supervisor engine or
routing engine failover will always trigger a link down at the peer router.
Answer: BC
QUESTION 2
Refer to the exhibit. A service provider would like to use Ethernet OAM to detect end-to-end connectivity failures between SP-SW1 and SP-SW2. In which two of these ways can you design this solution? (Choose two.)
A. Enable Y.1731 Connectivity Fault Management on the SP switches.
B. E-LMI PDUs must be forwarded over VPLS.
C. Cisco Discovery Protocol PDUs must be forwarded over the VPLS.
D. Use upward maintenance endpoints on the SP switches.
E. Enable IEEE 802.1ag Connectivity Fault Management on the SP switches.
Answer: DE
QUESTION 3
A network design shows two routers directly connected to an Ethernet switch using optical connections. There is an OSPF adjacency between the routers. In this design, which solution will ensure that interface down detection is reported as quickly as possible to the IGP?
A. optimized OSPF SPF timers
B. Bidirectional Forwarding Detection
C. automatic protection switching
D. optimized OSPF LSA timers
E. Ethernet OAM CFM monitoring
Answer: B
QUESTION 4
A network designer is working with a company to improve convergence at the Layer 2 control plane and decides to use LACP. Which of these components does LACP use to create the system ID?
A. LACP system priority and switch MAC address
B. LACP port priority and switch MAC address
C. LACP port priority and port number
D. LACP system priority and port number
Answer: A
QUESTION 5
How are community formats sent in SNMPv1 and SNMPv2c?
A. In both protocols they are encrypted.
B. In both protocols they are sent as clear text.
C. In SNMPv1 they are sent as clear text and in SNMPv2c they are encrypted.
D. In SNMPv1 they are sent as clear text and in SNMPv2c they are sent as part of an encrypted session.
Answer: B
QUESTION 6
You are deploying OSPF on a point-to-multipoint Frame Relay network. The remote sites do not need to be able to communicate with each other and there are a relatively small number of sites (scaling is not a concern).
How should you configure OSPF for this topology to minimize the additional routing information injected into the network and keep the configuration size and complexity to a minimum?
A. Configure the link at the hub router as OSPF point-to-multipoint and at the remote routers as OSPF point-to-point.
B. Configure the link as OSPF broadcast and configure the hub router to always be the designated router.
C. Configure the link as OSPF nonbroadcast and manually configure each of the remote sites as a neighbor.
D. Configure the link as OSPF broadcast and configure a mesh group towards the remote routers.
Answer: B
QUESTION 7
Which two practices should you implement to increase SNMPv1 security? (Choose two.)
A. Restrict access to the specific SNMP engine IDs in use.
B. Use ACLs to allow only specific IP addresses to poll SNMP.
C. Use a combination of alphanumeric characters for the community strings.
D. Use SNMP encryption for transport confidentiality.
Answer: BC
QUESTION 8
Refer to the exhibits. You have been asked to review a proposal for adding redundancy to the non-redundant network in Exhibit 1. Exhibit 2 shows the proposed redundant network. Which technology would provide faster convergence over the newly introduced layer 2 domains?
A. Bi-directional Forwarding Detection
B. Rapid Spanning Tree
C. Unidirectional Link Detection
D. Hot Standby Router Protocol
Answer: A
QUESTION 9
A service provider has a Resilient Ethernet Protocol ring running as a metro backbone between its locations in one city. A customer wants to connect one site with one box redundant to the Resilient Ethernet Protocol ring at two different service provider locations. How can this be done without producing any Layer 2 loops within the network design?
A. Spanning tree at the service provider side only must be enabled.
B. Spanning tree at the customer side only must be enabled.
C. Flex Links at the service provider side only must be enabled.
D. Flex Links at the customer side only must be enabled.
E. EtherChannel at the service provider side and the customer side must be enabled.
F. Spanning tree at the service provider side and the customer side must be enabled.
G. Flex Links at the service provider side and the customer side must be enabled.
Answer: D
QUESTION 10
Refer to the exhibit. Your company designed a network to allow server VLANs in a data center to span all access switches. In the design, Layer 3 VLAN interfaces and HSRP are configured on the aggregation switches. In which three ways should the design of the STP domain be optimized for server and application performance? (Choose three.)
A. Use loop guard on access ports.
B. Use PortFast on access ports.
C. Use root guard on access ports.
D. Align Layer 2 and Layer 3 forwarding paths.
E. Use BPDU Skew Detection on access ports.
F. Explicitly determine root and backup root bridges.
Answer: BDF
!!!RECOMMEND!!!
1.|2017 New 352-001 Exam Dumps (PDF & VCE) 499Q&As Download:
http://www.braindump2go.com/352-001.html
2.|2017 New 352-001 Study Guide Video:
https://youtu.be/mTLcNm1jZow
[2017-New-Exams]100% Success-Braindump2go 70-767 Questions 317q Instant Download[Q1-Q7] [2017 News]High Quality Braindump2go 352-001 VCE Exam Dump 499Q Free Share[11-20]
Comments are currently closed.