19 10 2013

QUESTION 50
The CLI utils dbreplication reset all was run on a Cisco Unified Communications Manager. However, replication failed to restart. Which course of action should be taken to resolve this issue?

A. Restart the replication from the Cisco Unified Communications Manager RTMT tool. B. Issue the CLI command utils dbreplication runtimestate
C. Issue the CLI command utils dbreplication reset
D. Issue the CLI command utils dbreplication clusterreset
E. Issue the CLI command utils dbreplication clusterreset all

Correct Answer: D Section: (none) Explanation

Explanation/Reference:
Database Replication Does Not Occur When Connectivity Is Restored on Lost Node
Symptom Database replication does not occur when connectivity is restored on lost node
recovery. You can verify the state of replication by using the methods given in the topic Replication Fails Between the Publisher and the Subscriber. Only use the following procedure if you have already tried to reset replication on the node, and have been unsuccessful.

Possible Cause: The CDR check remains stuck in a loop, due to a delete on device table. Recommended
Action
Step1 Run utils dbreplication stop on the affected subscribers. You can run them all at once. Step2 Wait until Step1completes, then, run utils dbreplication stop on the affected publisher
server.

Step3 Run utils dbreplication clusterreset from the affected publisher server. When you run the command, the log name gets listed in the log file. Watch this file to monitor the process status. The path to the follows:/var/log/active/cm/trace/dbl/sdi

Step4 From the affected publisher, runutils dbreplication reset all.

Step5 Stop and restart all the services on all the subscriber servers [or restart/reboot all the systems (subscriber servers)] in the cluster to get the service changes. Do this only afterutils dbreplication status shows Status 2.
QUESTION 52
What do you do next if after observing the result of your troubleshooting, the problem still exists?

A. Implement Acton Plan
B. Define the Problem
C. Consider the Possibilities
D. Create Action Plan
E. Gather Facts
F. Observe Results
G. Restart Problem-Solving
H. Process Problem Resolved

Correct Answer: C Section: (none) Explanation

QUESTION 58
When the command utils dbreplication status is executed on the Cisco Unified Communications Manager
CLI, which step should be taken next to check the database replication status?

A. View the activelog file
B. Run the same command on all nodes of the cluster
C. Restart the Cisco CallManager service.
D. The command utils dbreplication runtimetstate must be run on the publisher. E. The command utils dbreplication runtimestate must be run on the subscriber.

Correct Answer: A Section: (none) Explanation

Explanation/Reference:

QUESTION 59
Which QoS methodology combines strict priority queuing with class-based weighted fair queuing?

A. IP RTP Priority
B. Multilink
C. IP Frame Relay RTP Priority
D. RSVP E. LLQ

Correct Answer: E Section: (none) Explanation

Explanation/Reference:
Explanation: Link- http://www.cisco.com/en/US/tech/tk543/tk544/tk399/tsd_technology_support_sub- protocol_home.html

QUESTION 62
Which three Cisco IOS commands are required to configure a voice gateway as a DHCP server to support a data subnet with the IP address of 101.30.0/24 default gateway of 10.1.30.1/24? (Choose three)

A. ip dhcp pool
B. subnet 10.1.30.1 255.255.255.0
C. ip dhcp pool data
D. network 10.1.30.1/24
E. network 10.1.30.0 255.255.255.0
F. default-gw 10.1.30.1.24
G. default-router 10.1.30.1

Correct Answer: CEG
Section: (none)

642-427 Exam Dumps

Microsoft 70-680 Practise Tests (Question 21 – 30) Free Download Pass4sure and Lead2pass Cisco 300-206 Exam Question with PDF & VCE