web analytics

Braindump2go Free Microsoft Dumps Questions Collection

Latest Real Exam Questions and Answers to help you pass Microsoft and other Hot exam 100%!

[March-2018-New]Download 200-601 Exam Dumps VCE from Braindump2go[Q35-Q45]

2018 March New Cisco 200-601 Exam Dumps with PDF and VCE Free Updated Today! Following are some new 200-601 Real Exam Questions:

1.|2018 Latest 200-601 Exam Dumps (PDF & VCE) 88Q&As Download:
https://www.braindump2go.com/200-601.html
2.|2018 Latest 200-601 Exam Questions & Answers Download:
https://drive.google.com/drive/folders/0B75b5xYLjSSNWTIxdF9WZmZqMms?usp=sharing

QUESTION 35
Given the CIA triad elements, which ensures first that the data is encrypted and secure, second that the data is trustworthy, and third that the data is accessible by those who need it?

A. CIA
B. ICA
C. ACI
D. CAI

Answer: A

QUESTION 36
To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted by the switch, which command must be entered on the interface attached to the device?

A. switch(config-if)#mls qos trust cos
B. switch(config-if)#qos trust cos
C. switch(config-if)#profinet cos trust
D. switch(config-if)#trust qos cos

Answer: A

QUESTION 37
AP CAPWAP control traffic should be isolated from wireless client traffic.
Which scenario represents the correct configuration to support the SSIDs of this controller-based access point in FlexConnect local switching mode?

A. Missing
B. Missing
C. Missing
D. Missing

Answer: C

QUESTION 38
Refer to the exhibit. CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to output queue 1 threshold 1.

You have received feedback that some of these messages are not being received. Executing the show mls interface GigabitEthernet statistics command on L2SW4 results in:
L2SW4# show mls interface GigabitEthernet 1/1 statistics
< output omitted>
output queues dropped:
queue: threshold1 threshold2 threshold3
queue 0 0 0 0
queue 1 309232345 450 0
queue 2 300 10 0
queue 3 91 0 0
Repeating this command results in the counters incrementing for queue 1 threshold 1.
What are two options for reducing the packet loss on this interface while preserving the end-to-end DSCP marking? (Choose two)

A. Configure I/O#1 to mark this traffic with a different DSCP that is mapped to a less congested queue
B. Increase the buffer allocation for input queue 1
C. Increase the buffer allocation for output queue 1
D. Alter the service policy to police to a higher CIR
E. Change the egress queue map on L2SW4 to map this traffic to a less congested queue

Answer: CE

QUESTION 39
Refer to exhibit. The administrator has configured the following device IP settings, but did not keep track of which ports the devices were connected to. The administrator is able to ping each device but needs to update the network documentation to include the switch and interface where each device is connected. The administrator does not want to walk to each device and switch to track down the information.

Which steps below would you execute in sequence to document the switch and interface where each device is connected?
1. View the ARP table on L3SW1
2. View the ARP table on the administrator’s station
3. View the ARP table on L2SW4
4. PING all the devices
5. View the MAC address table on all switches
6. View the MAC address table on the administrator’s station

A. 2,4,5
B. 2,5,4
C. 4,3,6
D. 4,1,5

Answer: D

QUESTION 40
A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choose two)

A. DLR is designed for single network operation at the machine level
B. Moving to a linear topology will reduce the number of cables and so reduce risk of cable failure
C. DLR is the only resiliency technology that is supported by CIP Safety
D. Layer 2 resiliency protocols like REP and RSTP do not have a fast enough convergence time for motion control
E. Half of the network traffic goes clockwise on the ring and the other half counter- clockwise, reducing by 50% the impact of cable failure

Answer: AD

QUESTION 41
Which characteristic causes multimode fiber-optic cable to differ from single mode?

A. by allowing multiple network services in the same cable
B. shorter maximum network segment length for a given bandwidth
C. a wider variety of available connector types
D. use outdoors as well as indoors

Answer: B

QUESTION 42
Which command globally enables QoS on a Cisco Industrial Ethernet switch?

A. switch(config)#qos enable
B. switch(config)#mls queuing enable
C. switch#enable queuing
D. switch(config)#mls qos

Answer: D

QUESTION 43
You are making changes to a Stratix 5700 using an Add On Profile (AOP) and a controller which is on-line with RSLogix5000. When do the changes you have made get published to the switch?

A. While online in RSLogix 5000 software the changes made in the AOP are pushed to the switch after pressing the Set button.
B. All of the changes are automatically pushed to the switch.
C. Changes to the AOP can only be made from the switch, not in RSLogix 5000.
D. RSLogix 5000 will push the changes in the AOP to the Stratix 5700 when you right click on the switch, and choose download to switch

Answer: A

QUESTION 44
Refer to the exhibit. SW1, SW2 and virtual switch are connected in a loop. SW1 and SW2 are standard layer-2 switches.
Which loop prevention mechanism is best suited for use within this topology?

A. Per-VLAN Rapid Spanning Tree Protocol+
B. End-Host Mode
C. Multi-chassis EtherChannel
D. BPDU Guard

Answer: B

QUESTION 45
Refer to the exhibit. NAT has been configured on the router ‘GW’ and the IP addresses of router ‘GW’ have been configured properly. Users of PC1 and PC2 are able to ping the IP address
198.51.100.1 but are unable to reach any other IP addresses on the Internet. The ISP confirmed that their configuration is correct. Which option would likely correct the problem?

A. ip access-list extended ACL_OUTBOUND
permit ip 10.1.1.0 0.0.0.255 any
interface Ethernet1
ip access-group ACL_OUTBOUND out
B. interface Ethernet1
ip nat outside
C. interface Ethernet0
ip nat inside
D. ip route 0.0.0.0 0.0.0.0 198.51.100.1

Answer: D


!!!RECOMMEND!!!
1.|2018 Latest 200-601 Exam Dumps (PDF & VCE) 88Q&As Download:
https://www.braindump2go.com/200-601.html
2.|2018 Latest 200-601 Study Guide Video:
https://youtu.be/X0MHNJ5wJSc

, , , , , , ,

Comments are currently closed.